Fostoria VHC-32 Variable 208/240 Volt Controller

Click here for a larger image

We are an authorized distributor for Fostoria Industries, a manufacturer of infrared heating systems.

The Fostoria VHC-32 Variable Heat Controller is a solid-state power control designed to provide a convenient way to adjust heat output on electric infrared heating elements. The faceplate includes an ON/OFF switch that glows red when the controller is in use. It also includes the heat intensity control knob. Use the VHC-32 to control heaters on patios, in shelter houses or other protected outdoor environments. It is designed for use with 208 or 240 volt Fostoria Mul-T-Mount 3200 watt heaters. (222 MUL-T-MOUNT INFRARED HEATERS). It can operate quartz lamps or quartz tubes up to a maximum of 3200 watts.

The VHC-32 can be used with the following Fostoria heaters:
OCH-46-208V
OCH-46-240V
OCH-57-208V
OCH-57-240V
RPH-208-A
RPH-240-A
222 MUL-T-MOUNT

• 208/240 VAC single-phase single stage controller

• Built-in On/Off switch with surface plate included

• A triac to control heat settings from 10 to 100%.

• Designed for wall mounting in the same space a 4”x 4” electrical wall box would mount.

• Accommodates hardware for 1/2” conduit.

• Will operate:
  One (1) or two (2) quartz lamps
  totaling up to 3200W or
  One (1) or two (2) quartz tubes
  totaling up to 3200W.

• Caution: The initial current inrush of T3 quartz lamps is very high; as much as 10 – 15 times the steady state current. Operating the VHC-32 with more than two (2) 1600W quartz lamps may damage the control. This concern is not applicable to quartz tubes or other constant-resistance elements.

• Note: Faceplate may become warm to the touch during use. This is normal.

• Not for residential use.

• Must be mounted in a protected area (Not for unprotected outdoor use.)

  ---

INSTALLATION & WIRING

To install the VHC-32:

1. Carefully remove cover from controller (internal wiring is attached from inside of cover to rear of controller box) and mount box in wall. View below shows mounting-hole options. Note: If wires are accidentally pulled off the heat sink during installation, reference Wiring Diagram for correct reattachment.

2. Wire control to power source and heater as shown in wiring diagram using (4) wire nuts provided. Note that wires marked “L1” or “L2” can be attached to either incoming power lead. Also, the wire marked “H1” and the red wire coming from the heat sink can be wired to either lead going out to the heater.

3. Attach bonding (ground) wires under green screw in back of box.

4. Reattach cover to box being careful not to damage internal wiring.

Warning: ELECTRICAL SHOCK HAZARD
• Serious injury or death may occur.
• Disconnect from electrical supply before installing or servicing this product.
• Make certain the power source conforms to specifications on heater label.
• Always securely connect green wire from heater to bonding (ground) wire from electrical supply, not to a live or “hot” conductor.
• Use 12 AWG, 90° C rated copper wire only. Maximum 50 ft. run.
• Follow state, local and national electric codes (NEC).

ELECTRICAL SHOCK HAZARD
FIRE HAZARD
• Serious injury or death may occur.
• Not for residential use.
• Do not use in locations containing hazardous or explosive atmospheres.
• Do not use outdoors in wet conditions and in unprotected locations.

For field wiring, refer to the Installation manual included with your heater. All wiring must be performed by a licensed electrician.

Click here for a larger image

Replacement parts for VHC-32 shown below:
Rocker Switch Part No.: 3111700	Knob Part No.: 3183800	Cover Part No.: 8052500

Installation Instructions/Parts Manual in .pdf format (You must have the free Adobe Acrobat Reader plug-in.)

Other Fostoria products are also available.  © Copyright Fostoria Industries Inc., (a wholly owned subsidiary of TPI Corporation)

[ Home ] [ Up ]

	MOR ELECTRIC HEATING ASSOC., INC. 5880 Alpine Ave. NW - Comstock Park, MI 49321  USA Tel 616-784-1121 - 800-442-2581 - Fax 616-784-7775 - E-mail: sales@infraredheaters.com © Copyright 1999-2010 Mor Electric Heating Assoc., Inc.